How to flash Firmware on DMA Card 75T

Download and keep the DMA Cheats folder on your Second PC.
Download to the Main PC only those files that should be running on the Main PC according to the instructions.
Don't download and don't run DMA cheats on the Main PC.

1. Make sure that the switch on your DMA card is set to the "ON" position

2. Turn off the Main PC and install the DMA Card in PCI express slot (x1, x4 or x16) of your motherboard

3. Insert USB 3.0 cable into the JTAG port of your DMA card

4. Insert the other side of USB cable into a USB 3.0 port on the Second PC

5. Turn on Main and Second PC

6. Run SETUP.exe from folder DMA Cheats\1. DMA Card\75T\2. CH341SER driver\CH341PAR as admin

7. Select INSTALL

8. You should see a Driver Install Success!

successful driver installation for dma card 75t

9. Go to folder "3. Firmware installer" and run Zadig.exe as administrator

10. Click Options >> List All Devices

11. You will see device RS232-HS. Select it

12. Click on big button Replace/Reinstall Driver. Wait for installing the driver

replace driver to flash firmware on dma card 75t

13. Change name of your firmware .bin file to "test"

14. Move you firmware file (test.bin) to the folder 3. Firmware installer.

move firmware file to flash dma card 75t

15. Go to the folder 3. Firmware installer and run "flash" file

16. You should see process of flashing, which will take about 2 minutes

successful flashing process for dma card 75t

17. After the process is completed, turn off your Main PC and Second PC and turn off the power (switch on the power supply to position "0" or pull the power supply cable out of the socket) for 30 seconds

This is a mandatory step, don't ignore it

turn off the main PC's power supply after flashing firmware for dma card 75t

18. Connect USB cable to the DATA port on the DMA card and turn on your Main and Second PC

19*. If you have full emulated firmware from dma-cheats.com, go to folder 6. If you have full emulated firmware and follow the manual. You will receive a password from this folder from the manager when you purchase our firmware.

If you have not full emulated firmware, you don't need to follow this step.
If you bought a full firmware emulation anywhere other than dma-cheats.com, you don't need to follow this step either.

DMA Card Test

20. Go to the folder 4. DMA test\Full test\lone dma test

Run lone-dma-test.exe

Select 1. Full Test

lone dma test dma card 75t after flashing

< 60 MB/s — bad speed, you need to get a better USB Cable or try another USB 3 Port or another PCIe slot

>= 100 MB/s — good speed

>= 150 MB/s — great speed

If the test was failed, watch the video and read the troubleshooting below

Video Manual

Firmware Installer error

Firmware Installer Error

Make sure that you:

Connected USB cable to JTAG (CFG) port of DMA card and to second PC USB 3.0 port
Launching JTAG Firmware Installer on Second PC
Moved JTAG Firmware Installer to desktop
Moved firmware file (.bin) to desktop
If you are using a third-party DMA card, try using another Tool from the folder "If this manual doesn't work for your card".

Bad Test / Slow Speed

Bad Test / Slow Speeds

If speed test was failed:

Turn off Gaming-PC and unplug the power cord.
Unplug the DMA-USB from Radar-PC.
Press and hold the Gaming-PC power button for 15 seconds to unload any residual voltage.
Plug DMA - USB back into Radar - PC and reconnect the Gaming - PC power cord.
Power up the Gaming - PC.
Run Benchmark Tool and see if issues persist.

If speed test is slow:

~35-60 MB/s -> Make sure that you are on a USB 3.x cable and port

We recommend getting at least a 10gbit/s USB cable
Try different USB Ports on the second PC.
Usually USB 3.x ports are colored blue/red/orange/purple
USB 3.x ports usually have these icons next to them

~16-35 MB/s -> Most likely stuck in tiny algo

Try different PCIe ports and make sure that the BIOS settings are correct
If nothing else works try setting the pcie slot to gen3 / gen4 in bios.

Driver Installation Error

If certain peripherals not responding or behaving unusual or display is unresponsive/showing artefacts or behaving unusual:

Try different PCIe slots

DMA Failed to Connect

Check your USB cable
Open device manager on second PC
Search for FTDI Driver on USB category

Open folder DMA Cheats\2. Firmware\4. Driver for DMA Card
Find the driver you need
Right Click FTDI SuperSpeed-FIFO Bridge in device manager
Update Drivers with the extracted FTD3XX Drivers.
Make sure Second PC is fully updated and there are no windows updates pending
Check to make sure you are using a fast USB slot (cycle slots if necessary)

Where to download?

You will receive all the files necessary to set up a DMA card, Firmware, Kmbox, Fuser, Xim Matrix and our cheats when you purchase any product on our website (even if buy only cheat subscription for 30$, you will get ALL the files for DMA devices as well).

Firmware file (.bin) is unique and is developed for each customer individually, you can buy it here —

https://www.dma-cheats.com/firmware

You can also buy access to all the files for $5.

Pay with crypto — https://dmacheats.mysellix.io/product/access-to-dma-cheats-folder

Pay with debit/credit card — https://dmacheats.sellsn.io/product/a3503cce-549d-4b88-95ec-a63b72d588fe

tools, drivers for dma card, firmware, kmbox, fuser, dma cheats, xim matrix

See all Products →