DisplayPort Fuser Guide
Manual how to set up DP Fuser to use it with DMA card and solve possible errors.
You can buy our Fuser here — https://www.dma-cheats.com/fuser
Giude how to set up HDMI Fuser is located in the folder DMA Cheats
INSTALLATION
TROUBLESHOOTING
DOWNLOAD
Recommended Hardware
Recommended HDMI cable — HDMI 2.1 cable
Recommended DisplayPort cable — DP 1.4 cable
Your Second PC or Laptop should have at least 1 free HDMI port.
If you don't have a Second PC we recommend — Mini PC
Recommended OS — Windows 10 or 11
Connecting DP Fuser
1. On Second PC go to Display settings
2. Set the scale to 100%
3. Select the desired resolution
Important! The resolution and refresh rate of the screen must be supported by both monitors and Fuser.
If you have 2 monitors with the same specifications, then you need to set the resolution and refresh rate supported by Fuser on both monitors.
For example, I have 2 monitor 2K165hz, but Fuser supports 2K144hz, so I'll set 2560x1440 and 144hz.
If one of your monitors has a lower resolution or/and refresh rate, then you will need to lower the settings on the second monitor to the same values.
For example, if you have Main Monitor 2K165hz and Second Monitor with 1K60hz, then you should set 1920x1080 and 60hz on both monitors.
DisplayPort Fuser supports:
-
1920x1080@60HZ
-
1920x1080@144HZ
-
1920X1080@165HZ
-
1920X1080@240HZ
-
2560x1440@144HZ
-
2560x1080@165HZ
-
3440X1440@60HZ
-
3440X1080@100HZ
-
3840X2160@60HZ
4. Select the desired refresh rate (it should be supported by both monitors and Fuser as said in the point above)
5. Make the same settings on the Main Monitor:
-
Scale 100%
-
Resolution and Refresh rate as on the Second Monitor
6. Connect the Fuser according to the picture below.
Note that the Main Monitor is connected to the Fuser using a DisplayPort cable.
But the Second PC and Graphic card of Main PC are connected to the Fuser using HDMI cables
7. Connect the Fuser to the power supply and turn it on using the power button
8. On the remote control, select the previously set resolution and refresh rate.
I set 2560x1440 144hz, so I press the button 2K144
9. On the Second Monitor go to Diplay settings
10. In the section Multiple displays, select Duplicate these displays
It should turn out like this
11. Now press the Fusion button on the remote control or on the Fuser itself to broadcast the cheat from the Second Monitor to the Main one.
If the cheat is not running, then you will see a duplicate image from the Second Monitor on the Main one
If after completing all the points Fuser doesn't work for you, watch the video and read the solution of possible errors below.
Video Manual
Main Monitor doesn't work
If the main PC just shows a black screen and shows no signs of life, make sure that:
-
You have connected the DisplayPort and HDMI cables correctly
-
No other DP or HDMI cables are connected to the main monitor
-
The Fuser is plugged into an outlet and turned on using the red button
-
You selected the resolution and refresh rate supported by Fuser on the Second Monitor and pressed the button with the corresponding parameters on the Fuser remote control
If none of the above helped. Disconnect all cables and start following the instructions from the beginning
Monitors aren't working properly
If an image with an incorrect resolution or refresh rate is displayed on the main monitor, make sure that:
-
You're using the resolution and refresh rate supported by Fuser and have set it to me on both monitors
-
In the section Display settings on the Second PC you selected Duplicate these displays
No supported resolution
If Fuser doesn't support your resolution or screen refresh rate, then lower them to the closest values that are supported.
For example, if your monitor specs are 4K120hz, downgrade to 4K60hz or 2K120hz.
Note that this resolution and refresh rate must be supported by both of your monitors.
Remote doesn't work
Make sure you remove the plastic plug and insert the battery into the remote control.
Where to download?
You will receive all the files necessary to set up a DMA card, Firmware, Kmbox, Fuser, Xim Matrix and our cheats when you purchase any product on our website (even if buy only cheat subscription for 30$, you will get ALL the files for DMA devices as well).
You can also buy access to all the files for $5.
Pay with crypto — https://dmacheats.mysellix.io/product/access-to-dma-cheats-folder
Pay with debit/credit card — https://dmacheats.sellsn.io/product/a3503cce-549d-4b88-95ec-a63b72d588fe
