INSTALLATION
TROUBLESHOOTING
Firmware 100T Guide
This manual will work for our branded DMA Cards 100T and for some other brands.
Before installing firmware, make sure that you have .bin file. In some cases firmware can be already pre-installed on your DMA Card and you don't have to flash it again. Ask your seller about it.
You can buy our Firmware here — https://www.dma-cheats.com/firmware
DOWNLOAD
Recommended Hardware
Recommended USB cable — Purchase USB Cable
Not enough space for your DMA card? You can buy extender — Purchase PCIe Extender
If you don't have a Second PC, we recommend — Mini PC
Recommended OS — Windows 10 or 11
Flashing Firmware
-
Download and keep the DMA Cheats folder on your Second PC.
-
Download to the Main PC only those files that should be running on the Main PC according to the instructions.
-
Don't download and don't run DMA cheats on the Main PC.
1. Make sure that the switch on your DMA card is set to the ON position.
2. Turn off the Main PC and install the DMA Card in PCI express slot (x1, x4 or x16) of your motherboard.
3. Insert USB 3.0 cable into the JTAG port of your DMA card.
4. Insert the other side of USB cable into a USB 3.0/3.1/3.2 port on the Second PC.
5. Turn on your Main and Second PCs.
6. On the Second PC go to the folder DMA Cheats\2. Firmware\100T\1. CH341PAR driver\CH341PAR and run SETUP.exe.
7. Click INSTALL.
8. You should see a sign "Driver install success!"
9. On the Second PC go to folder DMA Cheats\2. Firmware\100T\2. Flashing tools and move CH347FPGATool folder to your desktop.
This is a mandatory step to move the folder to your dekstop, don't ignore it!
10. Move you firmware file (.bin) to the folder CH347FPGATool.
You will receive the firmware (.bin) file after purchasing it.
12. Open CH347FPGATool folder and run CH347FpgaDownloadTool.exe
13. In the FPGA column, select xc7a100t.
14. In the middle column, change from BIT to BIN.
15. Then click this button and select your firmware (.bin) file
16. Click this button to start flashing process.
17. Wait until the flashing process is complete. It may take 2-4 minutes.
18. After the process is completed, turn off your Main PC and Second PC and turn off the power (switch on the power supply to position "0" or pull the power supply cable out of the socket) for 30 seconds.
This is a mandatory step, don't ignore it!
19. Connect USB cable to the DATA port on the DMA card and turn on your Main and Second PCs.
20*. Some firmware requires to install driver on Main PC. If you bought firmware from our website, the Manager will send you the driver (if it's required). For some firmware driver is not required or it will be installed automatically.
21. On your Second PC go to folder DMA Cheats\2. Firmware\100T\3. DMA test.
And run lone-dma-test.exe.
Select 1. Full Test.
< 60 MB/s — bad speed, you need to get a better USB Cable or try another USB 3 Port or another PCIe slot
>= 100 MB/s — good speed
>= 150 MB/s — great speed
If the test was failed, watch the video and read the troubleshooting below
Video Manual
Firmware Installer Error
Make sure that you:
-
Connected USB cable to JTAG (CFG) port of DMA card and to second PC USB 3.0 port
-
Launching JTAG Firmware Installer on Second PC
-
Moved JTAG Firmware Installer to desktop
-
Moved firmware file (.bin) to desktop
-
If you are using a third-party DMA card, try using another Tool from the folder "If this manual doesn't work for your card".
Bad Test / Slow Speeds
If speed test was failed:
-
Turn off Gaming-PC and unplug the power cord.
-
Unplug the DMA-USB from Radar-PC.
-
Press and hold the Gaming-PC power button for 15 seconds to unload any residual voltage.
-
Plug DMA - USB back into Radar - PC and reconnect the Gaming - PC power cord.
-
Power up the Gaming - PC.
-
Run Benchmark Tool and see if issues persist.
If speed test is slow:
~35-60 MB/s -> Make sure that you are on a USB 3.x cable and port
-
We recommend getting at least a 10gbit/s USB cable
-
Try different USB Ports on the second PC.
-
Usually USB 3.x ports are colored blue/red/orange/purple
-
USB 3.x ports usually have these icons next to them
~16-35 MB/s -> Most likely stuck in tiny algo
-
Try different PCIe ports and make sure that the BIOS settings are correct
-
If nothing else works try setting the pcie slot to gen3 / gen4 in bios.
Driver Installation Error
If certain peripherals not responding or behaving unusual or display is unresponsive/showing artefacts or behaving unusual:
-
Try different PCIe slots
DMA Failed to Connect
-
Check your USB cable
-
Open device manager on second PC
-
Search for FTDI Driver on USB category
-
Open folder DMA Cheats\2. Firmware\4. Driver for DMA Card
-
Find the driver you need
-
Right Click FTDI SuperSpeed-FIFO Bridge in device manager
-
Update Drivers with the extracted FTD3XX Drivers.
-
Make sure Second PC is fully updated and there are no windows updates pending
-
Check to make sure you are using a fast USB slot (cycle slots if necessary)
Where to download?
You can download DMA Cheats folder here — https://www.dma-cheats.com/download
Firmware file (.bin) is unique and is developed for each customer individually, you can buy it here —
